mechanical and tribological properties of the tic tib2

(PDF) INFLUENCE OF PROCESSING PARAMETERS AND

In this paper the properties of the austenitic stainless steel reinforced with various volume fractions of TiB2 ceramics have been studied. The high temperature -high pressure (HP-HT) method of sintering was applied to the formation of composites.

1 Bonding structure and mechanical properties of Ti-B-C

Abstract. Nanocomposite coatings combining hard phases (TiB2, TiC) with amorphous carbon (a-C) were developed to provide a good compromise between mechanical and tribological properties for M2 steels used in a wide variety of applications such as cutting tools, bearings and gear mechanisms. Comparative Study of Physical, Mechanical and Tribological Jul 10, 2020 · Enhanced mechanical and tribological properties were observed for both the prepared composites compared to Al2024 alloy; this increment was higher for Al2024-TiB2 composite than Al2024-SiC composite. Al2024-TiB2 composite exhibits superior wear resistance with non-existence of plastic deformation and adhesion on the wear tracks.

Effect of Molybdenum on the Wear Properties of (Ti,Mo)C

Apr 03, 2018 · (Ti,Mo)C, TiB 2, and Mo 2 B particles reinforced Fe-based composite coatings were fabricated by laser cladding process. The effects of Molybdenum (Mo) on the microstructure and wear properties of the coatings were investigated. The results show that block-like or cuboidal TiB 2, Mo 2 B and flower-like (Ti, Mo)C ceramics reinforcements were formed in the coatings. Effect of TiB2 on the Phase Composition, Microstructure Mar 11, 2021 · Besides SiC, TiB 2 is also considered as potential reinforcing agent due to its excellent mechanical properties (hardness:~30 GPa, elastic modulus:~550 GPa, and flexural strength:over 500 MPa), high temperature stability (melting point 3225°C), high oxidation and corrosion resistance, and good thermal and electrical conductivity (60120 W · m 1 · K 1 and 10 6 S · cm 1, respectively)

Investigation of the properties of Al7075-HTC composites

Jan 27, 2021 · In this study, three different amounts of HTCs (0.25, 0.50, and 1.00 wt.%) produced from cellulose were used as a reinforcement material in Al 7075 by powder metallurgy for the first time. According to the mechanical, tribological, and corrosion test results, all of the mentioned properties of Al 7075 alloy were improved by reinforcing with HTCs. Mechanical and Tribological Properties of Spark Plasma Aug 22, 2017 · The effects of sintering temperature on densification and mechanical properties of composites have been investigated in detail. SiCTiB 2 and SiCTiB 2 TaC composites sintered at 2100°C showed high Vickers hardness value, i.e., 27.20±1.23GPa and 26.40±0.80GPa, respectively, under 1 kgf (9.81N) load.

Ni-Based Composite Coatings Reinforced with TiB2

Aug 23, 2020 · particles and the matrix, thereby improving the tribological properties. However, the WC particles are prone to settle at the bottom of the composite coating under a too low cooling rate, and the tribological properties deteriorate instead. TiB2 particles have high hardness, and excellent resistance to wear, oxidation and corrosion, Processing and characterization of the microstructure and Jun 05, 2021 · In the present research, aluminum metal matrix composites were processed by the stir casting technique. The effects of TiB2 reinforcement particles, severe plastic deformation through accumulative roll bonding (ARB), and aging treatment on the microstructural characteristics and mechanical properties were also evaluated. Uniaxial tensile tests and microhardness measurements

Structure and properties of cast Ni3Al/TiC and Ni3Al/TiB2

Investigation of mechanical and tribological properties and of corrosion resistance of composites based on intermetallic phase Ni3Al reinforced with particles of TiC and TiB2 Autorzy Fra, E. , Janas, A. , Kurtyka, P. , Wierzbiski, S. Study on Mechanical Alloying of TiB2 Particulate TiB2 particulate reinforced titanium matrix composites were prepared by mechanical alloying and spark plasma sintering. Volume fraction of TiB2 powders in the composites are 5%, 10%, 15%. The effect of milling time and the volume fraction of reinforcement on microstructure and properties of the composites were studied. The results show that with increasing milling time, the size of powder

The Ceramic Composite Coating (TiC+TiB2) by ESD on

Tang J. Mechanical and tribological properties of the TiC TiB2 composite coating deposited on 40Cr-steel by electro spark deposition. Applied Surface Science 2016; 365:202208 Tala, . The densification and mechanical properties of a TiC and Jan 16, 1996 · Yujin Wang, Mianyi Yao, Zhiyi Hu, Haixia Li, Jia-Hu Ouyang, Lei Chen, Sijia Huo, Yu Zhou, Microstructure and mechanical properties of TiB2-40 wt% TiC composites:Effects of adding a low-temperature hold prior to sintering at high temperatures, Ceramics International, 10.1016/j.ceramint.2018.09.048, 44, 18, (23297-23300), (2018).

Tribological properties and microstructures of Al2O3-TiC

Sep 26, 2017 · Moreover, TiO 2 is the most effective additive for improving sintering and mechanical properties . Thus, it was considered that the production of Al 2 O 3-TiO 2 was beneficial in improving the wear resistance of the upper layer. Furthermore, the production of Ti 3 Al, TiC-Fe 3 Al eutectic and TiC-Al 2 O 3 also improved the wear resistance of Comparison of mechanical and tribological properties of Jan 01, 2010 · On the other hand, the TiC and TiB 2 are hard ceramic materials that can be used to increase the wear resistance of the composite to which they belong. This study compares the mechanical adherence, tribological and corrosion properties of a cermet that has TiC or TiC TiB 2 and NiTi as a matrix. The friction coefficient and the mass loss as a function of time were obtained from the tribological

Drop us a Line

Contact Address

Mountain Drive, Kensington,
Newyork, USA.
12 345 890123
Mon-Fri, 9am until 6pm
[email protected]
We reply within 24 hours